San4o 11 #1 Posted April 1, 2020 Проблема в следующем! Раздатка всегда активна и не выключает полный привод!ошибка 1444! Менял электро привод раздатки, прозвонили провода от блока управления ,установил новые фрикционы! Мозги отвозил на проверку, сказали целые!абс есп работают все отлично! Share this post Link to post Share on other sites
Richmond 183 #2 Posted April 1, 2020 52 минуты назад, San4o сказал: Проблема в следующем! Раздатка всегда активна и не выключает полный привод!ошибка 1444! Менял электро привод раздатки, прозвонили провода от блока управления ,установил новые фрикционы! Мозги отвозил на проверку, сказали целые!абс есп работают все отлично! У тебя случаем нет тумблеров принудительного влкючения полного привода? Дима RP одно время всем ставил. Share this post Link to post Share on other sites
San4o Topic Author 11 #3 Posted April 1, 2020 20 минут назад, Richmond сказал: У тебя случаем нет тумблеров принудительного влкючения полного привода? Дима RP одно время всем ставил. Нет, это все вырезано и возвращено в сток! Это первое на что грешил! Share this post Link to post Share on other sites
Richmond 183 #4 Posted April 1, 2020 24 минуты назад, San4o сказал: Нет, это все вырезано и возвращено в сток! Это первое на что грешил! Если вырезано, значит вырезано не правильно и где-то контачит плюс либо масса. Share this post Link to post Share on other sites
San4o Topic Author 11 #5 Posted April 1, 2020 5 часов назад, Richmond сказал: Если вырезано, значит вырезано не правильно и где-то контачит плюс либо масса. Всё прозвонили, не на массу не на плюс между собой не звонятся! Вырезано все грамотно! Share this post Link to post Share on other sites
Richmond 183 #6 Posted April 1, 2020 2 часа назад, San4o сказал: Всё прозвонили, не на массу не на плюс между собой не звонятся! Вырезано все грамотно! А ошибки какие? Share this post Link to post Share on other sites
San4o Topic Author 11 #7 Posted April 2, 2020 5 часов назад, Richmond сказал: А ошибки какие? C1444 Share this post Link to post Share on other sites
San4o Topic Author 11 #8 Posted April 8, 2020 Заменил fdcm в 3 раз, все тоже самое! Чуда не произошло! Share this post Link to post Share on other sites
Richmond 183 #9 Posted April 9, 2020 В 02.04.2020 в 08:23, San4o сказал: C1444 C1444-TRANSFER CASE MOTOR OVERUSEPossible Causes INTERMITTENT TRANSFER CASE MOTOR OVERUSE TRANSFER CASE SELECTOR SWITCH FINAL DRIVE CONTROL MODULE ---------------------- Diagnostic Test 1. DTC IS ACTIVE NOTE: Diagnose and repair any system voltage or Transfer Case related DTCs in the FDCM before continuing with this test. Ignition on, engine not running. With the scan tool, Clear Stored DTCs. Test drive the vehicle. During the test drive, move the Transfer Case Selector Switch to each position several times in accordance with the Service Information. With the scan tool, select View DTCs. Does this DTC reset? Yes >> Go to 2 No >> Go to 4 2. TRANSFER CASE SELECTOR SWITCH Using the wiring diagram/schematic as a guide, inspect the wiring and connectors relative to this circuit. While monitoring the scan tool data relative to this circuit, wiggle test the wiring and connectors. Were any problems found? Yes >> Repair as necessary. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. No >> Go to 3 WK TRANSFER CASE - ELECTRICAL DIAGNOSTICS 21 - 955 C1444-TRANSFER CASE MOTOR OVERUSE (CONTINUED) 3. FINAL DRIVE CONTROL MODULE Ignition off. Replace the Transfer Case Selector Switch in accordance with the Service Information. Ignition on, engine not running. With the scan tool, Clear Stored DTCs. Test drive the vehicle. During the test drive, move the Transfer Case Selector Switch to each position several times in accordance with the Service Information. With the scan tool, select View DTCs. Does this DTC reset? Yes >> Replace the Final Drive Control Module in accordance with the Service Information. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. No >> Test Complete. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. 4. INTERMITTENT WIRING AND CONNECTORS The conditions necessary to set this DTC are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors. While monitoring the scan tool data relative to this circuit, wiggle test the wiring and connectors. Look for the data to change or for the DTC to reset during the wiggle test. Were any problems found? Yes >> Repair as necessary. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. No >> Test complete. Share this post Link to post Share on other sites
San4o Topic Author 11 #10 Posted April 11, 2020 В 09.04.2020 в 14:07, Richmond сказал: C1444-TRANSFER CASE MOTOR OVERUSEPossible Causes INTERMITTENT TRANSFER CASE MOTOR OVERUSE TRANSFER CASE SELECTOR SWITCH FINAL DRIVE CONTROL MODULE ---------------------- Diagnostic Test 1. DTC IS ACTIVE NOTE: Diagnose and repair any system voltage or Transfer Case related DTCs in the FDCM before continuing with this test. Ignition on, engine not running. With the scan tool, Clear Stored DTCs. Test drive the vehicle. During the test drive, move the Transfer Case Selector Switch to each position several times in accordance with the Service Information. With the scan tool, select View DTCs. Does this DTC reset? Yes >> Go to 2 No >> Go to 4 2. TRANSFER CASE SELECTOR SWITCH Using the wiring diagram/schematic as a guide, inspect the wiring and connectors relative to this circuit. While monitoring the scan tool data relative to this circuit, wiggle test the wiring and connectors. Were any problems found? Yes >> Repair as necessary. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. No >> Go to 3 WK TRANSFER CASE - ELECTRICAL DIAGNOSTICS 21 - 955 C1444-TRANSFER CASE MOTOR OVERUSE (CONTINUED) 3. FINAL DRIVE CONTROL MODULE Ignition off. Replace the Transfer Case Selector Switch in accordance with the Service Information. Ignition on, engine not running. With the scan tool, Clear Stored DTCs. Test drive the vehicle. During the test drive, move the Transfer Case Selector Switch to each position several times in accordance with the Service Information. With the scan tool, select View DTCs. Does this DTC reset? Yes >> Replace the Final Drive Control Module in accordance with the Service Information. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. No >> Test Complete. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. 4. INTERMITTENT WIRING AND CONNECTORS The conditions necessary to set this DTC are not present at this time. Using the wiring diagram/schematic as a guide, inspect the wiring and connectors. While monitoring the scan tool data relative to this circuit, wiggle test the wiring and connectors. Look for the data to change or for the DTC to reset during the wiggle test. Were any problems found? Yes >> Repair as necessary. Perform the TRANSFER CASE VERIFICATION TEST-VER 1. No >> Test complete. Спасибо! Все сделал! Заменил фишку на моторчик раздатки, все заработало! Share this post Link to post Share on other sites